angle of skew

angle of skew 基本解释

网络  歪斜角

机械

重点词汇

• anglen. 角, 角度, 角落 vi. 钓鱼, 谋取, 博取, 斜向移动, 转变角度 vt. 使转动角度, 在...钓鱼, 获取
• ofprep. 的, 属于
• skewa. 斜的, 歪的 n. 歪斜, 偏态家庭关系 vi. 歪斜, 侧转 vt. 使歪斜, 曲解 [计] 扭斜; 歪斜; 偏斜

angle of skew 双语例句

1. 1、 The effects of the gradient index, skew angle and aspect ratio on the stability of the non-conservation FGM skew thin plate were analyzed.
   结果表明，非保守FGM斜板的临界颤振荷载随梯度指标和夹角的增大而减小，随长宽比的增大而增大。
2. 2、 Calculation and Design for caster angle of Cardan Shaft in Skew Rolling Mill
   斜轧机的万向联结轴倾角的计算与设计
3. 3、 An instrument for measuring the angle of magnetic dip ( as from an airplane). A Chinese Italics Skew Detection Algorithm
   从飞机上测量磁倾角的仪器。中文斜体印刷字倾斜角度的检测算法
4. 4、 The calculation for the caster angle of cardan shaft in the skew rolling mill is more complicated than that in general rolling mill.
   斜轧机万向联接轴倾角的计算比一般纵轧机复杂，而且影响其倾角大小的因素也较多。
5. 5、 The paper introduces a kind of design methods of simple-supported beam bridge with large skew angle. This method compares with other design method of treating large skew angle, has no replaceable superiority in many conditions.
   介绍一种大斜交角度简支梁桥设计方法，该方法与其它处理大斜交角度的桥梁设计方法相比，在很多情况下均具有不可替代的优越性。
6. 6、 This article presents the calculating formula of the caster angle of cardan shaft and discusses principles for designing rational cardan shaft in the skew rolling mill.
   本文介绍了斜轧机万向联接轴倾角的计算公式，并论述了合理设计万向联接轴的几条原则。
7. 7、 Several mapping methods of spiral angle of skew spur gear on the spot are introduced.
   介绍了现场测量斜齿圆柱齿轮螺旋角β的几种方法。
8. 8、 In the end, we used this procedure to analyze the influence of the oblique angle to the bearing points and inter-force, and discuss the influence of the ratio ( the bending moment to the wrest moment) to the skew bridge.
   最后利用该程序分析了斜交角对支点反力以及梁内力的分布影响，讨论了弯扭刚度比对格栅梁的影响。
9. 9、 The paper makes hydro-technological model test for a certain skew transporter bridge with multi line large angle, to counter the condition of multi-line skew transporter bridge with larger skew angle and the characteristics now of calculation method that
   该文针对多线斜交桥渡在斜交角度较大的情况下，目前尚缺少理论及经验计算方法的特点，对某多线大角度斜交桥渡进行了水工模型试验。
10. 10、 The optimum angle of skew is determined by using the method of skew integration.
    采用斜槽积分的方法，探讨了斜槽对各次谐波转矩的影响，确定了一个最佳的斜槽角度。
11. 11、 Analysis of Influence of Skew Angle on Seismic Response of Continuous Skew Girder Highway Bridges
    斜交角对公路连续斜交梁桥地震反应的影响分析