spacer
spacer是什么意思、spacer怎么读
读音：['speɪsə]
['speɪsə]
spacer 基本解释
n. 垫片; 隔板; 衬垫; 撑挡
spacer 词性变化
spacer 词组短语
- metal spacer
- spacer bar
- spacer flange
- spacer gel
- spacer ring
- spacer sleeve
- spacer spool
- spacer tube
- tank spacer
- bow spacer
spacer 双语例句
- 1、
The change of the spacer layer can be realized by etching or depositing.
间隔层的改变可以采取刻蚀或镀膜的方法来实现。 - 2、
Drag onto the page to add washer or spacer with adjustable inside and outside diameters.
拖到绘图页后，可以添加内径和外径都可调整的垫圈或垫片。 - 3、
Fasten the spacer sleeve with grease.
使用润滑脂固定间隔垫圈。 - 4、
Position spacer on the lower part of the spoiler.
将垫圈放在扰流板下部上。 - 5、
Push spacer sleeve No.11 onto the valve body.
将隔套编号11推到阀体上。 - 6、
Insert spacer plate underneath lower hinge.
将隔板插入下铰链的下面。 - 7、
Before installing the compressor check whether the aluminium spacer sleeve is inserted.
安装压缩机之前，请检查是否插入了铝隔套。 - 8、
The17-mm spacer must be removed before mounting a spare wheel.
安装备胎之前，必须拆卸17-mm的垫圈。 - 9、
Remove spacer ring from inner joint.
从内球头拆下隔环。 - 10、
Separate striker and spacer from vehicle.
从车辆上拆下扣击板和垫片。 - 11、
The bypass ports are cut into the cylinder just below the exhaust ports and the transfer channels are formed by a hollow between the steel cylinder and the aluminum spacer ring.
绕道港口切割成气缸仅低于排气口和转移的渠道，形成由一个空心之间的钢瓶和铝间隔环。 - 12、
This plant is specially engaged in research, development and manufacture of the special equipment for static sealing spacer.
本厂是从事静密封垫片专用设备研究开发、造的专业厂家。 - 13、
The spacer ring is a precision detail made of non-magnetic alloy or polymer.
该间隔环是精确详细的非磁性合金或高分子的。 - 14、
Mechanism of hole-to-hole millisecond delay blasting and behaviour of soft spacer at the bottom of boreholes are discussed.
本文分别论述了孔间微差爆破和炮孔底部柔性垫层的作用机理。 - 15、
Tops of spacer bars shall be flush with the tops of the bearing bars.
定位钢筋的顶部应该与支撑梁的顶部齐平。 - 16、
The spacer must be removed when fitting the spare wheel.
安装备用轮胎时必须拆下垫圈。 - 17、
Spiral wound gaskets for pipe flanges Ensure the ground clip is on spacer slot.
管法兰用缠绕式垫片应确保接地夹片在垫片槽上。 - 18、
Install new spacer on the tension bow.
在张力撑弓上安装新的间隔垫圈。 - 19、
The function and property of LCD spacer is discussed.
论述了液晶显示器（CD）衬垫料的作用和性能要求。 - 20、
The spacer blocks bring the hook-and-loop pieces in contact with each other.
间隔器座，使钩和环件，在相互接触。 - 21、
Secure the new spacer with the blind rivets, see corresponding section in replacing hood frame.
用空心铆钉固定新的间隔垫圈，请参见更换软篷框架中的相应部分。 - 22、
Fit the supplied spacer plate if necessary.
必要时请安装所提供的隔板。 - 23、
Remove spacer ring and timing gear with a conventional puller.
用常规拉具拆卸隔环和正时齿轮。 - 24、
Place chisel or spacer under the halfshaft flange.
将凿子或厚垫片放在半轴法兰下面。 - 25、
Clip in spacer blocks and press in body-bound rivets.
用卡子夹在隔块内，并压入车身铆钉。 - 26、
Affix front spoiler to the retaining strip and fasten it with the sheetmetal screw and spacer sleeve.
将前扰流板固定在束带上，用自攻螺钉和间隔垫圈固定。 - 27、
Fasten the front end with the sheetmetal screws and the spacer sleeves.
用自攻螺钉和间隔垫圈紧固前端。 - 28、
Place a wooden support from the spacer to the additional support, position additional support and lower the transmission.
将间隔垫圈的木质支撑件放在附加支撑件上，放置附加支撑件然后放下变速器。