crack growth
crack growth是什么意思、crack growth怎么读
读音：[kræk ɡrəʊθ]
[kræk ɡroʊθ]
crack growth 基本解释
裂纹扩展；龟裂增长
重点词汇
crack growth 双语例句
- 1、
Application of Immune Algorithm in the Low-cycle Fatigue crack growth Rate of Steam Turbine Rotor
免疫算法在汽轮机转子低周疲劳裂纹扩展速率中的应用 - 2、
Fatigue crack growth and fatigue life evaluation for welded steel bridge members with initial crack
具初始裂纹钢桥梁焊接构件疲劳裂纹扩展和疲劳寿命计算 - 3、
Finite element study of the effects of compressive load on the fatigue crack growth in Paris Region
压载荷对疲劳裂纹在Paris区内扩展影响的有限元研究 - 4、
Novel Arithmetic of Fatigue crack growth under Random Loading
随机荷载作用下疲劳裂纹扩展新算法 - 5、
Influence of couple stresses on crack growth and its scale effect
偶应力对裂纹扩展的影响及其尺度效应 - 6、
The crack growth orientations under simple tension was gained by finite element analysis.
通过有限元分析，得出了固体推进剂单向拉伸时裂纹扩展方向。 - 7、
Many studies in the related area of stress corrosion or subcritical crack growth use simplified test systems.
许多有关应力腐蚀或亚临界裂纹发展领域的研究使用了简化的试验系统。 - 8、
Debonding is a main form of interfacial crack growth of fiber-reinforced composites.
脱粘是纤维增强复合材料界面裂纹扩展的主要表现形式。 - 9、
Subcritical crack growth is one of the main causes of time-induced failure in rock engineering.
亚临界裂纹扩展是岩体工程破坏时间效应的原因之一。 - 10、
The Research on Low-cycle Fatigue crack growth Rate of Steam Turbine Rotor Steel Based on Immune-Genetic Algorithm
基于免疫遗传算法的汽轮机转子钢低周疲劳裂纹扩展速率研究 - 11、
Influence of Microstructure and Frequency on Fatigue crack growth Rate of Ti_3Al-based Alloy
显微组织及频率对Ti3Al基合金疲劳裂纹扩展速率的影响 - 12、
The fatigue testing of the heterogeneous plates showed that the mechanical heterogeneity affected the fatigue crack growth rate.
试验表明，力学不均匀性影响疲劳裂纹扩展速率。 - 13、
Study on Multiaxial Cyclic Stress of Varying Amplitude Fatigue crack growth Rate
多轴变幅加载下疲劳裂纹扩展速度的研究 - 14、
Fatigue crack growth probability model based on stress ratio
考虑应力比的疲劳裂纹扩展概率模型 - 15、
A Model Unifying Both Fatigue Nucleation and crack growth Based on Continuous Accumulated Damage
基于连续累积损伤的疲劳启裂和裂纹扩展的统一模型 - 16、
Based on Pairs equation, the recursion relation of crack growth length has been deduced.
根据这一递推式，推导出数个循环载荷作用下裂纹扩展长度的近似算法。 - 17、
Theoretical and Applied Research on crack growth and Damage Evolution
裂纹扩展与损伤演化理论与应用研究 - 18、
Experimental Study on crack growth of RC Beam Strengthened with CFL
CFL加固RC梁裂纹扩展的实验研究 - 19、
During fatigue loading stable crack growth was observed over the en-tire range of crack lengths investigated.
在疲劳加载中，裂纹扩展始终是稳定的。 - 20、
In the tie girder boxes crack growth was detected near the crack tip.
在系杆箱型梁中裂纹尖端附近检测到裂纹的扩展。 - 21、
The crack surfaces in the web and flange were subjected to visual examination in order to evaluate crack growth regions.
为了估计各裂纹扩展区，对翼缘和腹板的裂纹表面进行了宏观检验。 - 22、
To meet the development of steels used for the large engineering machinery, fatigue crack growth rates of a high strength low alloy steel HG80 and welded joint were investigated.
为适应大型工程机械焊接用钢需要，对低合金高强度钢HG80及其焊接接头的疲劳裂纹扩展速率进行了研究。 - 23、
An investigation of the effects of mean and alternating stresses on short fatigue crack growth under uniaxial loading is reported.
本文报道单向加载下平均应力和交变应力对疲劳短裂纹生长的影响。 - 24、
Particula emphasis has been devoted to the influence of load ratio and microstructure on behaviour of near-threshold fatigue crack growth.
着重分析了载荷比和显微结构对门坎值附近裂纹扩展行为的影响。 - 25、
Structure ceramics; crack growth; Grinding cracks;
工程陶瓷；裂纹扩展；磨削裂纹； - 26、
The structure integrity of HK40 reformer tube is studied in respect of the controlling parameter of creep crack growth, the critical crack length and the residual life.
分别从蠕变裂纹扩展的控制参数，临界裂纹长度及剩余寿命三方面对HK40转化管进行了结构完整性研究。 - 27、
The influence of specimen's thickness on JR curves, the curve of driving force for crack growth and the method of its determination are also discussed.
研究了JR曲线受试样厚度的影响。还介绍了弹塑性裂纹扩展推力曲线及其确定方法。 - 28、
Three variables as temperature, load frequency and stress ratio are the critical parameters affecting fatigue crack growth behaviour in metallic material.
温度、载荷频率和应力比是影响材料疲劳裂纹扩展行为的主要因素。 - 29、
Influences of Welding Residual Stresses on Fatigue crack growth of Butt Weld Plate
对接焊缝残余应力对疲劳裂纹扩展的影响 - 30、
Initiation of stable crack growth Goal: Stability, Scalability, Performance and Security.
稳态裂纹扩展的开始目标：稳定性，可扩展性，性能和安全。