chamfer
chamfer是什么意思、chamfer怎么读
读音：[ˈtʃæmfə(r)]
[ˈtʃæmfər]
chamfer 基本解释
n. 斜切面; 削角
chamfer 词性变化
复数：chamfers现在分词：chamfering过去分词：chamfered过去式：chamfered第三人称单数：chamfers
chamfer 词组短语
chamfer 详细解释
noun
- 斜切面；削角
a cut made along an edge or on a corner so that it slopes rather than being at 90˚
chamfer 双语例句
- 1、
This paper analyzes the lack of traditional settingout method and the advantage of digitalization settingout method when analyzing settingout of chamfer stake in cubic meter of earth and stone.
分析了土石方工程中坡口桩放样时，传统放样方法的不足和数字化放样方法的优点。 - 2、
Select those front edges and chamfer them then click apply and chamfer it again but this time with a lower value.
选择前面的边并倒角，然后单击应用并以较低的值再次倒角。 - 3、
chamfer ends of all screw threads
将所有螺丝端部斜切 - 4、
REchamfer: Defect on radii and chamfer; defective chamfer such as nicks that are considered to be repairable.
重新倒角：可被重新修复的倒角缺陷，例如划痕。 - 5、
The effects of rolling parameters such as plate width, roll contours, chamfer and straight chamfer parameters on the contact pressure distribution were studied.
研究结果表明，在轧制能力范围内，轧件越宽，轧辊采用凹辊型可以使辊身部的辊间压力分布更为均匀； - 6、
Optional accessories are: to plug, referral chamfer, outlet.
可选配件有：地插座、下线槽、出线口。 - 7、
chamfer: The flat surface formed by cutting away the sharp edges of two meeting surfaces.
倒角：两个表面相交处，通过切掉尖锐边缘形成的平面。 - 8、
Drag onto the page. Right-click to set chamfer angle.
拖到绘图页上。右击可设置切角角度。 - 9、
The specialized inspector inspects the bore diameter, pitch, chamfer and finish degree of bore wall.
加工完成后由专门检验员检验孔径、孔距、倒角大小、孔壁光洁度。 - 10、
But for Reminder: the dimensions related to big chamfer are not major characteristic.
但提醒：大倒角的尺寸并不大特点。 - 11、
Core drills. A core drill consists of the chamfer, body, neck, and shank, as shown in Fig.12.2.
空心钻包括斜面、钻头体、钻颈和钻柄，如图12.2所示。 - 12、
Single type angle drills: Use to machine chamfer for hole of glass, stones etc. Various type and specification.
独立倒角钻头：用于玻璃孔、石材孔倒角使用。各种型号及规格。 - 13、
In order to miniaturize the millimeter wave circuit system, this study improved the traditional chain SIW filter and brought forward a new type of compact configuration with chamfer angle.
为了实现毫米波电路系统小型化，对传统链式SIW滤波器进行改进，提出了一种新型的带倒角的紧缩结构SIW滤波器。 - 14、
If you need the capability study on the big chamfer for300 pcs, then we have to measure at CMM ( 3D) as GFT method.
如果您需要300个大倒角能力的研究，那么我们在三坐标测量机（3D）测量GFT的方法。 - 15、
What is the nominal chamfer size?
什么是公称倒角尺寸？ - 16、
Conclusion: Amalgam post and core technique is conservative in restoring molars for its curved root canal, big root furcation and large pulp chamfer.
结论：对于根管弯曲、叉大、室大或C型根管的磨牙，银汞桩核修复效果良好。 - 17、
Also, the chamfer of the stay vanes entrance and the surface roughness of the flow channel were optimized by the numerical investigations.
亦对固定导叶入口冲角、涡壳壁面粗糙度对流动的影响进行了定量分析。 - 18、
Programming Method of Milling of chamfer and Fillet Based on$ TC_DP
基于＄TCDP铣削斜面及倒圆角的程序编制方法 - 19、
Based on physical simulation of edge rolling process in Trimming-Free Plate rolling method, the affection of V rolling and chamfer rolling on the plate profile is analyzed.
基于中厚板无切边轧制法中立轧轧边变形的物理模拟，分析了平辊立轧与倒棱轧制对中厚板断面形状的影响。 - 20、
Carefully remove smaller edges or burrs on the chamfer of the crankshaft flange with an oilstone if necessary.
如有必要，请用油石仔细去除曲轴法兰倒棱上的小边或毛刺。 - 21、
Drag to add perpendicular lines with adjustable chamfer size.
拖动此形状，可添加切角可调的垂直线。 - 22、
Or just the dimensions related to big chamfer?
或者只是尺寸大倒角？ - 23、
Making drilling by using numerical control drilling machine and ensuring the dimensions of horizontal direction and vertical direction of holes and chamfer through accuracy of the drilling machine.
数控铣削：对尖轨前端工作边及贴合面的加工时采用大型数控龙门铣床加工，通过专用夹具、专用刀具和对应的数控程序保证尖轨前端各个断面的尺寸和形貌。 - 24、
Rolling bearing chamfer dimension limits
GB/T274-1991滚动轴承装配倒角极限 - 25、
In addition, this paper compares this technology with gear chamfer technology of grinding wheels and finds the advantages of flexibility abrasive deburring technology.
并与砂轮齿轮倒角技术进行了对比，总结出了柔性研磨回转体去毛刺技术的优点。 - 26、
After too large tooth resultant force is eliminated, tooth chamfer bone is OK proper motion rehabilitate, of the tooth become loose degree also return to normal subsequently;
当过大的牙合力消除后，牙槽骨可以自行修复，牙齿的松动度也随之恢复正常； - 27、
The control strategy based on constant force will result in an uneven chamfer for its characteristics in nature.
控制策略的基础上不断的部队将结果在粗糙的槽的特点大自然。 - 28、
Fit the sealing ring at the correct position in the vacuum pump so that it is flush with the lower edge of the chamfer in the rotor.
将密封圈安装在真空泵的正确位置，以便密封圈与转子倒棱的下边缘平齐。 - 29、
The Study and Realization of Auto Marking chamfer and Taper in UG
倒角和锥度自动标注在UG中的研究和实现 - 30、
Marking chamfer and taper is a routine work in Mechanical drawing.
在机械制图中，通常需要进行大量的倒角和锥度的标注工作。
chamfer 英英释义
noun
verb