dowel
dowel是什么意思、dowel怎么读
读音：[ˈdaʊəl]
[ˈdaʊəl]
dowel 基本解释
n. 暗榫
dowel 词性变化
复数：dowels过去分词：dowelled过去式：dowelled
dowel 词组短语
dowel 详细解释
noun
- 暗榫
a small piece of wood, plastic, etc. in the shape of a cylinder , used to fix larger pieces of wood, plastic, etc. together
dowel 双语例句
- 1、
When doing so, watch out for dowel sleeves and studs.
执行此操作时，请注意销套和螺杆。 - 2、
The two dowel pins align the cap and base of the housing.
用两个定位销将座罩和轴承座基础对准。 - 3、
The carpenter gauged the dowel with calipers.
那木匠用卡钳估量暗榫。 - 4、
Remove carrier, check dowel sleeve for damage and replace if necessary.
拆下托架，检查定位销套筒有无损坏，必要时予以更换。 - 5、
Make sure that the dowel sleeves of the fastening screws are seated correctly in the seal.
确保紧固螺钉的销套正确就位于密封件中。 - 6、
The connection type between the vertical guide plate of the vertical adjusting mechanism and the positioning plate can adopt compression-fitting connection or dowel pin type connection.
纵向调节机构的纵向导板与定位板之间的连接方式可采用压紧连接或柱销式连接。 - 7、
The dowel pin of the engine mounting must sit correctly into the cut-out on the engine carrier.
发动机支座的定位销必须正确地放入发动机托架的切口。 - 8、
Once your dowels are cut to size, spread a thin layer of glue in all the dowel holes and along the edges of the mating boards.
做好圆榫后，在要对接的两边和榫孔内都涂上薄薄一层胶水。 - 9、
Remove stem assembly ( A) and lock setting by drilling hole and inserting dowel pin ( C).
拆卸阀杆总成（A），并且通过钻孔锁定设置和插入定位销（C）。 - 10、
A rational method of disposal for a the dowel bar is proposed through test-in-place and finite element analysis.
提出了传力杆的合理布置方式，并通过现场试验和数值模拟进行了分析和验证。 - 11、
Check that the dowel sleeves are installed correctly.
检查定位销套筒是否安装正确。 - 12、
Glue injecting and dowel driving machine He bent the iron bar as if it had been of rubber.
喷胶及圆棒榫打入机他把铁棒象胶一般地弄弯了。 - 13、
Repairing young root-fractured permanent anterior teeth with immediate titanium dowel internal fixation in alveolar bone through canal
根管内加齿槽骨钛桩内固定即刻修复年轻恒前牙根折年轻恒前牙感染根管内血管再生的动物实验研究 - 14、
Check dowel sleeves to ensure that they are seated correctly or insert two new dowel sleeves in crankcase.
检查销套，确保它们正确就位，或在曲轴箱中插入两个新销套。 - 15、
Diagram-body gap dimensionsthe dowel sleeves may have to be removed for subsequent assembly.
车身间隙尺寸图在后续装配工作中可能需要拆下销套。 - 16、
Check the position of the dowel pin.
检查定位销的位置。 - 17、
The transverse joints, longitudinal joints, isolation joints, including dowel bar construction technology were introduced too.
介绍横向接缝、纵向接缝、隔离接缝这三种接缝的施工工艺。 - 18、
Pull off dowel sleeves from the fuel injectors.
从喷油器拔出销套。 - 19、
Check that the dowel sleeves are present and seated properly.
检查销套是否存在并已正确入位。 - 20、
Check that dowel sleeves and studs are present.
检查销套和螺杆是否存在。 - 21、
Tooling Plate: Standard dowel locating holes and accurately milled locating slots.
模具板：标准定位桩孔，定位准确磨槽。 - 22、
Make sure that grease does not enter the receiving bores for the dowel pins.
一定不要让油脂进入定位销孔中。 - 23、
In course of processing the shaft and dowel type parts, the V-shape block location is replaced by the double-cylinder location.
本文对轴、销类用V形块定位和双圆柱定位的定位误差进行了分析。 - 24、
Fit a dowel pin here to keep the adjacent parts aligned.
在这里装一个定位销，是相邻的两个部件对准。 - 25、
Make sure that the two dowel sleeves are not lost.
千万不要丢失这两个销套。 - 26、
As ahead tooth, it has an ideal effect for dowel crown of casting and metal board, so as for beautiful and reducing lose of bone.
对于前牙，为了美观和减缓牙槽骨的吸收，采用铸造桩冠加金属翼板的修复方法，可以取得较理想的效果。 - 27、
Splitting forces are higher and dowel action is greater with the use of large diameter bars.
剪切力较高，销栓作用比大直径钢筋更有用。 - 28、
dowel cutting-to-length and chamfering machine circle mouton collar pyramid coat
圆棒榫截断及倒角机角锥形羊皮大圆领大衣 - 29、
Be careful with the dowel sleeve on the chain housing.
小心链条罩上的销套。 - 30、
Carefully remove and install the dowel sleeve.
拆卸和安装销套时务必小心。
dowel 英英释义
noun